Tag Archives: loading pens

New Cattle Working Pen

On February 20th our new cattle holding/working pen had progressed to this.

Hubby and I have been working everyday on the pen when the weather permitted.  We were delayed in the beginning due to problems finding the lumber we needed.  One of our neighbors, Mr. All, has a portable sawmill and sold us 20 of the 1 x 6 x 16 boards to get us started.  We then finally found a sawmill that took private orders and we bought 100 of the boards.  Most sawmills that we contacted don’t take private orders anymore and only sell to commercial builders such as mining operations.

100 oak boards from Bennett’s Sawmill in Lowmoor.

First row of posts are boarded and this side of the pen faces Little Mountain Road. We put heavy woven wire on first and then put the boards on top of that. We did this to prevent the cattle and calves from sticking their heads through the fence and breaking the boards. We’re learning from EXPERIENCE!!

Post holes are dug using a drill and our Kubota tractor. We are drilling into a bank of slate and sometimes had to use our big tractor and its front loader to press on the drill to force it into the slate and break it up.

Next row of posts are dug and post put in the ground with Quikrete.

And some bracing rocks are placed in the holes for durability.

This is the roll of wire that we placed between the posts and the boards.

The is the outside of the pen next to the main road.

This is the second section of boards and woven wire. We put boards on both sides of the posts for a sturdier loading chute. This needs to be sturdy because if the cows or calves are going to get honery getting on the truck, this is the spot where they’ll do it. They’ll try to back out, turn around or go over if they’re really anxious.

From this angle you can see the double layer of boards reinforcing the woven wire

This is another angle from the end of the pen to see the reinforced chute.

This gate is at the entry of the loading chute.The chute opens to an eight foot chute that narrows into a four-foot chute. The eight foot gate will swing from the narrow chute to the wider chute depending on what we are loading, cows or calves.

This four foot gate was then hung at the end of the chute where the trailer will load. You can also see another short gate about half way down the chute to help control turning and backing. Cattle are more apt to go into a wider space at the other end and that’s why we start with a 8 ft space that  narrows as you get toward the end of the chute.

This section is where the wider chute will be and the next we will board up. The posts are set and now we put the boards on. I might mention the posts are treated but the boards are not. We are using 3 inch screws to mount the boards. Once those green boards dry they’ll make the chance of coming out because the boards will shrink around the screws.

This is another section of the pen that we expanded from the old pen. We were experiencing lots of pushing and shoving when trying to separate 50 – 75 head of cattle at the same time. This section will have a gate that opens on both sides at the end of the pen toward the scale house. We can release them into the barnlot or if we still need to do some separating we can release them back in to the loading section.

Yes we have a scale house. The scales with in this building are state certified every year. We can watch the growth of the calves, we can check the weight of the cows or bulls and we can get an idea of how much weight is going to the market before they’re loaded on the truck.

This all I have for now but will continue the saga when the pen is completely finished and we can send a load of fall calves that we’ve weaned and been holding for the completion of the pen and hopefully a price increase.  I’m hopeful it will be completed this week!!!

Cattle Working Pens

Hubby and I spent most of February tearing out our old loading pen.  It was well over 50 years old and was worn out.  Instead of repairing like we normally do we decided to start over with this section of the pen.  The far end with the working head chutes and calf pens are on the opposite end and were redone three years ago.

This is the working part of the pen we completed three years ago.

This is the working part of the pen we completed three years ago.

Head chute for medical and castrating.  We consider this one of the best investments we've made in regards to working our cattle.  Hubby is less likely to get hurt, less stress on the calves and our daughter is learning to use it too!

Head chute for medical and castrating. We consider this one of the best investments we’ve made in regards to working our cattle. Hubby is less likely to get hurt, less stress on the calves and our daughter is learning to use it too!

 

 

 

 

 

 

 

 

 

 

The boards have been torn off the posts and cut up for kitchen woodstove firewood.  We recycle as much as possible.  The old posts will be cut up for the big woodstove.

The boards have been torn off the posts and cut up for kitchen woodstove firewood. We recycle as much as possible. The old posts will be cut up for the big woodstove.

We’ve rehung some gates, tightened up some posts, and put in some posts.  Now, we wait for our lumber to arrive which has been an unexpected delay.  Most of the private lumber mills in the area will only cut for commercial folks.  Here’s some pictures of the work we’ve done so far and I’ll post more as we get the work completed!  I’ve definitely used muscles that have been lazy for some time!!!dscn9079

Fence posts dug, posts placed, quikrete poured and hardened.

Fence posts dug, posts placed, Qickrete poured and hardened.

Heavy equipment used to set some gate posts that we didn't replace.

Heavy equipment used to set some gate posts that we didn’t replace.

Rotted off gate posts at scale house.

Rotted off gate posts at scale house.

Area of most work yet to be done.

Area of most work yet to be done.

Some of the existing gates that we will use again.

Some of the existing gates that we will use again.

dscn9007 dscn9005 dscn9003

We rehung these gates after we replaced the posts.

We rehung these gates after we replaced the posts.

Generator used to drill the hinge holes in the posts.

Generator used to drill the hinge holes in the posts.

Kubota tractor we used to drill the holes for the posts.

Kubota tractor we used to drill the holes for the posts.

We used our milkcans to haul water for the Quikrete

We used our milkcans to haul water for the Quikrete

The Massey Ferguson was used to haul in the new fence posts and hauling the pallet of Quikrete.

The Massey Ferguson was used to haul in the new fence posts and hauling the pallet of Quikrete.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOW WE WAIT!!